分享Subcon包工而已的价钱

暗恋小王子

如题，小弟想请教一下现在subcon 包工而已的价钱是多少？（Johor 区）
1) 绑铁1kg = RM??
2) BRC 1m2 = RM??
3) Alumimiun Formwork 1m2 = RM??
4) Timber Formwork 1m2 = RM??
5) Concrete 1m3 = RM??
6）通常外劳一个月多少钱？没有OT跟有OT会差多少？

因为我觉得我Subcon好像当我水鱼来劏，每次扣他钱他就说“这个价钱哪里做到？” 干!!!虽说我是刚毕业，可是用计算机算一下，他好像还好赚过我们maincon。


如果不太方便分享在这里可以PM我，我也会跟你们分享一下我Subcon 的天价是多少。

vincent8351

人工贵了，价钱好像还停留在10年前。

howann1990

1) 绑铁1kg = RM0.5
2) BRC 1m2 = Nil
3) Alumimiun Formwork 1m2 = Nil
4) Timber Formwork 1m2 = RM24-26
5) Concrete 1m3 = Nil

(Sarawak Rate)

暗恋小王子

Sarawak 哪里？刚好我们在Kuching有project

lek0212

1) 绑铁1kg = RM0.30
2) BRC 1m2 = RM1.5
4) Timber Formwork 1m2 = RM15
5) Concrete 1m3 = RM15

有人知道现在total sub R.C work (屋身而已） rm5.5/ ft2 能做吗？ Klang valley area

Porto

1. Reinforcement Bar = RM0.30-RM0.50/kg
2. BRC Wire Mesh = RM1.50-RM2.00/m2
3. Alum. Formwork = RM60-RM80/m2 (Fair Faced Concrete)
4. Ordinary/ Ply. Formwork = RM15-RM20/m2
5. Concrete = RM25-RM30/m3

其实QUANTITY／PROJECT 越大，价钱越便宜。

而 HOUSING， HIGH RISE， INFRA （DRAIN， SUMP，CULVERT），或大工程如大桥，水坝等又会有差别。

SITE WORKING CONDITION ＆ REQUIREMENT 也是。

lek0212

请问有total sub R.C works subcon 介绍吗？ gongsigong 太慢，价钱ok的话公司打算sub 出去了。

暗恋小王子

Porto 发表于 16-5-2016 03:28 PM
1. Reinforcement Bar = RM0.30-RM0.50/kg
2. BRC Wire Mesh = RM1.50-RM2.00/m2
3. Alum. Formwork = RM60-RM80/m2 (Fair Faced Concrete)
4. Ordinary/ Ply. Formwork = RM15-RM20/m2
5. Concrete = RM25-RM30 ...

Porto, 我想请教一下为什么Aluminum Formwork 还贵过 timber formwork？RM60 - RM80 是包工包料还是人工而已？请问你是那里拿到这个rate的？

Porto

暗恋小王子 发表于 19-5-2016 09:34 PM
Porto, 我想请教一下为什么Aluminum Formwork 还贵过 timber formwork？RM60 - RM80 是包工包料还是人工而已？请问你是那里拿到这个rate的？

通常用ALUM FORMWORK 是要用于有 QUALITY 的 FAIRFACED 表面。当然价钱就比较贵，这只是人工而已，不包括SYSTEM FORMWORK。

我的这个ALUM FORMWORK 人工价钱是要达到 JAPAN INTERNATIONAL STANDARD （JIS）或相等于 ASTM STANDARD 的QUALITY。表面不可以有一滴点凹凸。整个SYSTEM FORMWORK 是要跟着 SHOP DRAWING 来跑， 哪相对来说贵很多。

如果，你只是 NORMAL STRUCTURAL (EXAMPLE, HIGH RISE BUILDING)，只把TIMBER FORMWORK 换去 ALUM FORMWORK，那价钱就便宜多多。还是要看你的 SUBCON 会习惯ALUM FORMWORK 吗？如果习惯，很能上手了，那TIMBER FORMWORK 和 ALUM FORMWORK 的价钱可以一样。

(For normal concrete structural used, some sub-contractor can only get used with old style formwork (timber), in this case theirs work might be slower if they have to use alum formwork which they are not familiar with. By then, m2 per day produced by the worker might be lower than m2 per day if they use timber formwork, in this case rate will be higher)

Of course for those sub-contractor specialized in this system formwork, rate will be equally same or even lower, because the advantages of alum. formwork is to save time & cost (cost in long term). Yet, it's still all depend the type of building you are constructing. High Rise building with all typical slabs, beams & columns then you can expect lower labour rate for alum. formwork system.

其实你也可以拿多一点QUOTATION 来比较。

howann1990

暗恋小王子 发表于 21-4-2016 09:29 AM
Sarawak 哪里？刚好我们在Kuching有project

民都鲁阿^_^